access negative compression levels from command line
for both compression and benchmark modes.
also : ensure proper propagation of parameters
through ZSTD_compress_generic() interface.
added relevant cli tests.
Silence a Coverity warning about 'windowSize' being uninitialized.
(Yes, nothing that calls this routine actually uses the windowSize
value. Still, appeasing Coverity is pretty harmless in this case.)
This makes it easier to explain that nbWorkers=0 --> single-threaded mode,
while nbWorkers=1 --> asynchronous mode (one mode thread on top of the "main" caller thread).
No need for an additional asynchronous mode flag.
nbWorkers>=2 works the same as nbThreads>=2 previously.
Produces 3 statistics for ongoing frame compression :
- ingested
- consumed (effectively compressed)
- produced
Ingested can be larger than consumed due to buffering effect.
For the time being, this patch mostly fixes the % ratio issue,
since it computes consumed / produced,
instead of ingested / produced.
That being said, update is not "smooth",
because on a slow enough setting,
fileio spends most of its time waiting for a worker to complete its job.
This could be improved thanks to more granular flushing
i.e. start flushing before ongoing job is fully completed.
The compression % is no longer correct,
since it's no longer possible to make direct correlation
between nb bytes read and nb bytes written
due to large internal buffer inside CCtx
(exacerbated with --long).
The current "fix" is to no longer display the %.
A more complex solution will have to count exactly how much data has been consumed and compressed internally, within CCtx buffers.
when cli is compiled without MT support,
invoking ZSTD_p_nonBlockingMode result in an error code.
This patch only sets ZSTD_p_nonBlockingMode when ZSTD_MULTITHREAD is set, meaning there is MT support.
The error code could also be intentionnally ignored (there is no side effect).
This new parameter makes it possible to call
streaming ZSTDMT with a single thread set
which is non blocking.
It makes it possible for the main thread to do other tasks in parallel
while the worker thread does compression.
Typically, for zstd cli, it means it can do I/O stuff.
Applied within fileio.c, this patch provides non-negligible gains during compression.
Tested on my laptop, with enwik9 (1000000000 bytes) : time zstd -f enwik9
With traditional single-thread blocking mode :
real 0m9.557s
user 0m8.861s
sys 0m0.538s
With new single-worker non blocking mode :
real 0m7.938s
user 0m8.049s
sys 0m0.514s
=> 20% faster
This fixes the following crash:
$ touch exists
$ programs/zstd -r examples/ -o exists
zstd: exists already exists; not overwritten
Segmentation fault (core dumped)
* programs/fileio.c (FIO_compressMultipleFilenames):
Handle the case where we're not overwriting the destination.
Reported at https://bugzilla.redhat.com/1530049
This patch restores capability for each file to receive adapted compression parameters depending on its size.
The bug breaking this feature was relatively silly :
setting a parameter with a value "0" is supposed to be a no-op.
Unfortunately, it would pin down compression parameters as if they were manually set,
preventing later automatic adaptation.
Unfortunately, I'm currently short of a test case that could check this situation and trigger an error.
Compression parameters selection between tableID 0,1,2,3 is largely internal,
leaving no trace to outside world, not even in frame header.
Fixes issue where, when `zstd --format=lz4` is fed an input larger than 128KB,
the read overruns the input buffer. This changes Zstd to use LZ4 with chained
64KB blocks. This is technically a breaking change in that some third party
LZ4 implementations may not support linked blocks. However, progress should not
be allowed to be stopped by such petty concerns as backwards compatibility!
we lose a warning message :
when a job size is chosen < minimum job size for multithreading,
it is automatically resized to minimum size.
If this information is really useful, it should be present in zstd.h now.
removed the other 2 code paths (single thread, and ZSTDMT ones)
keeping only the new advanced API, for easier code coverage.
It shall also fix identified issue with Visual Studio
which doesn't have ZSTD_NEWAPI defined.
UTIL_getFileSize() used to return zero on failure.
This made it impossible to distinguish a failure from a genuine empty file.
Both cases where coalesced.
Adding UTIL_FILESIZE_UNKNOWN constant has many consequences on user code,
since in many places, the `0` was assumed to mean "error".
This is no longer the case, and the error code must be actively checked.
It was multiple reasons stacked :
- Visual use a different code path, because ZSTD_NEWAPI is not defined
- fileio.c sends `0` as `pledgedSrcSize` to mean `ZSTD_CONTENTSIZE_UNKNOWN` (fixed)
- ZSTDMT_resetCCtx() interpreted `0` as "empty" instead of "unknown" (fixed)
when determining compression parameters
to compress one file only.
For multiple files, it still "bets" that files are going to be small.
There was also a bug recently added in ZSTD_CCtx_loadDictionary_advanced()
making it incapable to use pledgedSrcSize to determine compression parameters.
Yann Collet
Conrad Meyer
Nick Terrell
Pádraig Brady
Yann Collet
W. Felix Handte