* Replaced a non-breaking space and an en dash with a plain space and
a hyphen.
* This means the files are simple ASCII and less likely to run into
codepage issues.
- do not test level 0, as it is converted into level 3,
which feels strange when compressing multiple levels
- Use direct synchronous mode when a single worker is requested.
access negative compression levels from command line
for both compression and benchmark modes.
also : ensure proper propagation of parameters
through ZSTD_compress_generic() interface.
added relevant cli tests.
zstd bench module can focus on decompression speed _only_.
This is useful when trying to measure performance
on large input data compressed using a high level
as compression time becomes problematic (too long).
This mode is triggered by command : zstd -b -d
Problem was : in such a mode,
measured decoding speed was > 10% slower
than in nominal mode (compression + decompression),
making decompression benchmark mode much less useful.
This patch fixes the issue.
It's not completely clear why, but
moving the `memcpy()` operation sooner in the pipeline fixed it.
I can still measure some difference, but it is in the < 2% range,
so it's much more tolerable.
also : it doesn't matter anymore in which order are selected
commands `-b` and `-d`.
The combination always triggers bench_decodeOnly mode.
Silence a Coverity warning about 'windowSize' being uninitialized.
(Yes, nothing that calls this routine actually uses the windowSize
value. Still, appeasing Coverity is pretty harmless in this case.)
by invoking time() once per batch, instead of once per compression / decompression.
Batch is dynamically resized so that each round lasts approximately 1 second.
Also : increases time accuracy to nanosecond
This makes it easier to explain that nbWorkers=0 --> single-threaded mode,
while nbWorkers=1 --> asynchronous mode (one mode thread on top of the "main" caller thread).
No need for an additional asynchronous mode flag.
nbWorkers>=2 works the same as nbThreads>=2 previously.
added some test
also updated relevant doc
+ fixed a mistake in `lz4` symlink support :
lz4 utility doesn't remove source files by default (like zstd, but unlike gzip).
The symlink must behave the same.
Produces 3 statistics for ongoing frame compression :
- ingested
- consumed (effectively compressed)
- produced
Ingested can be larger than consumed due to buffering effect.
For the time being, this patch mostly fixes the % ratio issue,
since it computes consumed / produced,
instead of ingested / produced.
That being said, update is not "smooth",
because on a slow enough setting,
fileio spends most of its time waiting for a worker to complete its job.
This could be improved thanks to more granular flushing
i.e. start flushing before ongoing job is fully completed.
this happened on 32-bits build when requiring a too large input buffer,
typically on wlog=29, creating jobs of 2 GB size.
also : zstd32 now compiles with multithread support enabled by default
(can be disabled with HAVE_THREAD=0)
The compression % is no longer correct,
since it's no longer possible to make direct correlation
between nb bytes read and nb bytes written
due to large internal buffer inside CCtx
(exacerbated with --long).
The current "fix" is to no longer display the %.
A more complex solution will have to count exactly how much data has been consumed and compressed internally, within CCtx buffers.
when cli is compiled without MT support,
invoking ZSTD_p_nonBlockingMode result in an error code.
This patch only sets ZSTD_p_nonBlockingMode when ZSTD_MULTITHREAD is set, meaning there is MT support.
The error code could also be intentionnally ignored (there is no side effect).
This new parameter makes it possible to call
streaming ZSTDMT with a single thread set
which is non blocking.
It makes it possible for the main thread to do other tasks in parallel
while the worker thread does compression.
Typically, for zstd cli, it means it can do I/O stuff.
Applied within fileio.c, this patch provides non-negligible gains during compression.
Tested on my laptop, with enwik9 (1000000000 bytes) : time zstd -f enwik9
With traditional single-thread blocking mode :
real 0m9.557s
user 0m8.861s
sys 0m0.538s
With new single-worker non blocking mode :
real 0m7.938s
user 0m8.049s
sys 0m0.514s
=> 20% faster
This fixes the following crash:
$ touch exists
$ programs/zstd -r examples/ -o exists
zstd: exists already exists; not overwritten
Segmentation fault (core dumped)
* programs/fileio.c (FIO_compressMultipleFilenames):
Handle the case where we're not overwriting the destination.
Reported at https://bugzilla.redhat.com/1530049
Yann Collet
Baldur Karlsson
Jesse Talavera-Greenberg
Yann Collet
Conrad Meyer
systemcrash
ne-sted
Nick Terrell
Pádraig Brady