128 lines
3.2 KiB
Plaintext
128 lines
3.2 KiB
Plaintext
##
|
|
## tinyproxy.conf -- tinyproxy daemon configuration file
|
|
##
|
|
|
|
#
|
|
# Name of the user the tinyproxy daemon should switch to after the port
|
|
# has been bound.
|
|
#
|
|
User nobody
|
|
Group nogroup
|
|
|
|
#
|
|
# Port to listen on.
|
|
#
|
|
Port 8888
|
|
|
|
#
|
|
# If you have multiple interfaces this allows you to bind to only one. If
|
|
# this is commented out, tinyproxy will bind to all interfaces present.
|
|
#
|
|
#Listen 192.168.0.1
|
|
|
|
#
|
|
# Timeout: The number of seconds of inactivity a connection is allowed to
|
|
# have before it closed by tinyproxy.
|
|
#
|
|
Timeout 600
|
|
|
|
#
|
|
# Where to log the information. Either LogFile or Syslog should be set,
|
|
# but not both.
|
|
#
|
|
Logfile "/var/log/tinyproxy.log"
|
|
# Syslog On
|
|
|
|
#
|
|
# Set the logging level. Allowed settings are:
|
|
# Critical (least verbose)
|
|
# Error
|
|
# Warning
|
|
# Notice
|
|
# Connect (to log connections without Info's noise)
|
|
# Info (most verbose)
|
|
# The LogLevel logs from the set level and above. For example, if the LogLevel
|
|
# was set to Warning, than all log messages from Warning to Critical would be
|
|
# output, but Notice and below would be suppressed.
|
|
#
|
|
LogLevel Info
|
|
|
|
#
|
|
# PidFile: Write the PID of the main tinyproxy thread to this file so it
|
|
# can be used for signalling purposes.
|
|
#
|
|
PidFile "/var/run/tinyproxy.pid"
|
|
|
|
#
|
|
# Include the X-Tinyproxy header, which has the client's IP address when
|
|
# connecting to the sites listed.
|
|
#
|
|
#XTinyproxy mydomain.com
|
|
|
|
#
|
|
# Turns tinyproxy into a TCP tunnel which connects the local computer on
|
|
# 'Port' to the remote computer's port. No processing is done when using
|
|
# tinyproxy as a tunnel. If you want to connect to an upstream proxy use
|
|
# the "Upstream" directive below.
|
|
#
|
|
#Tunnel some.remote.computer:port
|
|
|
|
#
|
|
# Turns on upstream proxy support.
|
|
#
|
|
#Upstream some.remote.proxy:port
|
|
|
|
#
|
|
# This is the absolute highest number of threads which will be created. In
|
|
# other words, only MaxClients number of clients can be connected at the
|
|
# same time.
|
|
#
|
|
MaxClients 100
|
|
|
|
#
|
|
# These settings set the upper and lower limit for the number of
|
|
# spare servers which should be available. If the number of spare servers
|
|
# falls below MinSpareServers then new ones will be created. If the number
|
|
# of servers exceeds MaxSpareServers then the extras will be killed off.
|
|
#
|
|
MinSpareServers 5
|
|
MaxSpareServers 20
|
|
|
|
#
|
|
# Number of servers to start initially.
|
|
#
|
|
StartServers 10
|
|
|
|
#
|
|
# MaxRequestsPerChild is the number of connections a thread will handle
|
|
# before it is killed. In practice this should be set to 0, which disables
|
|
# thread reaping. If you do notice problems with memory leakage, then set
|
|
# this to something like 10000
|
|
#
|
|
MaxRequestsPerChild 0
|
|
|
|
#
|
|
# The following is the authorization controls. If there are any access
|
|
# control keywords then the default action is to DENY. Otherwise, the
|
|
# default action is ALLOW.
|
|
#
|
|
# Also the order of the controls are important. The incoming connections
|
|
# are tested against the controls based on order.
|
|
#
|
|
Allow 127.0.0.1
|
|
Allow 192.168.1.0/25
|
|
|
|
#
|
|
# The location of the filter file.
|
|
#
|
|
#Filter "/etc/tinyproxy/filter"
|
|
|
|
#
|
|
# If an Anonymous keyword is present, then anonymous proxying is enabled.
|
|
# The headers listed are allowed through, while all others are denied. If
|
|
# no Anonymous keyword is present, then all header are allowed through.
|
|
# You must include quotes around the headers.
|
|
#
|
|
#Anonymous "Host"
|
|
#Anonymous "Authorization"
|