Original recording by Ryding.
http://freesound.org/people/Ryding/
Found by Anth0rx, edited by paramat.
Add and use 'default.node_sound_snow_defaults()' function.
Since meta secret field is blank on any keys (default:key) obtained using
/give, the game will crash if you attempt to use one of these. This follows
along the principle that the game should never have any reason to crash.
Return to previous parameters interval = 1, chance = 2.
Compensates for the increase in default active block radius.
Large amounts of lava cooling at once is known to overload sound
creation, producing error messages.
This implements a node-timer based leafdecay mechanism, and exposes
an API to use it in mods.
The API is documented in game_api.txt.
`default.register_leafdecay(leafdecaydef)`
`leafdecaydef` is a table, with following members:
{
trunks = { "default:tree"}, -- nodes considered trunks
leaves = { "default:leaves", "default:apple"}, -- nodes considered leaves
radius = 3, -- activates leafdecay this far from the trunk
}
The algorithm will drop `leaves` items in the area if no `trunks` are found
in the `trunk_radius` sized area around the position of the leaf. If a node
listed in `leaves` has a group `leafdecay_drop > 0`, then the item is dropped,
otherwise the item is removed but not dropped.
The algorithm also implements a value `default.leafdecay_speed` (default
15) which can be modified to increase or decrease of the leaf decay. The
algorithm will vary the actual speed a bit to introduce randomness.
Leaf decay is randomized by 0.1 seconds to reduce the chance that
decay happens many times on the same second interval. This requires
nodetimer_interval to be set to values lower than 1.0 to have an
effect.
The leaves will decay between 2 and 10 seconds after digging the trunk,
and happen at non-integer second intervals.
-- The API was added by sofar.
Now that the missing 'default_dig_snappy' sound has been added we can
remove the dirt dig sound from the table. All nodes that use the
leaves defaults table have group 'snappy' so 'default_dig_snappy' now
becomes their default dig sound.
I recently made glass footstep and dig gains too low, raise slightly.
Change dirt dug gain from above-maximum 1.5 to maximum 1.0.
Reduce gain of footsteps: stone, dirt, gravel, wood, metal
Raise gain of leaves footstep.
Some nodes with the snappy group (wool, glass pane, seeds) were missing
sound when dug with a sword.
Adding the sound causes it to be used for glass pane, so define a 'dig'
sound in the 'node sound glass defaults' table, use the footstep sound.
Adding the sound also causes it to be used for seeds which deliberately
have no dig sound, so add an empty sound override for seed dig.
Reduce the gain of the glass footstep sound which was excessively loud.
Add some freesound members to license.txt.
Make lava cooling ABM use a new group 'group:cools_lava'.
Nodes other than water can cool lava. We assume snowblock and ice melt,
turn to water and cool lava.
Leave 'group:water' present temporarily to not break mod liquids.
Credit to tenplus1 for the suggestion to generalise for mod use.
Mods can add mod nodes to 'group:spreading_dirt_type' enabling the
function to work with mod nodes.
Add some nodes to this group.
Removing 'dirt_with_grass' etc. from 'neighbors' stops the ABM action
running everywhere and constantly, on the dirt nodes immediately below
the surface nodes. Now the action only runs in the rare case of a dirt
node with neighbouring air, grass decorations or snow.
Remove check for air above to allow grass to spread under light-
transmitting nodes such as fences, walls, plants. This causes spread
under slabs, stairs and glass, when near air, but seems worth it.
Remove unnecessary check for nil node.
With thanks to contributor tenplus1
Remove leaf cache and globalstep accumulator limiter
Use 'pos' instead of 'p0'
Remove non-essential 'group:liquid' from 'neighbors'
Increase chance value to 10 to compensate for disabled cache
Disable 'catch-up' to avoid the ABM often becoming 10 times more
intensive
Remove use of 'do preserve' bool, instead simply 'return'
Remove unnecessary checks for 'd' and 'd == 0'
Don't 'get' n0, use already present 'node' instead
Swap order two conditionals so that the one most likely is first
Add a global 'intersects protection' function to functions.lua for
checking if a specified volume intersects with a protected volume.
A 3D lattice of points are checked with an adjustable interval.
Add a global 'sapling on place' function to avoid duplicated code in
nodes.lua.
Allow water to turn cobble slab and stairs to turn into mossy versions.
There is no crafting recipe for mossy stairs and mossy slabs, the
stair/slab API has been modified to allow for a recipeitem that
is `nil`, which will omit adding a crafting recipe for these two
items. The API documentation is updated.
The slabs and stairs will turn mossy when water is adjacent, just like
cobblestone. You can either farm mossy versions by placing them in
water for a while, then collecting them, or run water over your craft.
Adds a minor helper function that allows efficient retrieval of
several inventories from a node inventory. We use this helper to
quickly retrieve the items in chests, vessel shelves, book shelves
and furnaces, and return these with the nodes itself to the TNT caller.
The TNT caller then performs the entity physics, and we don't need
to do anything else.
We disable TNT doing anything with bones.
We expose a bug in the code that drops the items - metadata was lost
entirely. This patch corrects that by properly copying the metadata
and creating the drops list inclusive metadata.
This changes how dirt blocks turn to dirt_with -grass, -dry_grass
or -snow.
Previously, dirt that was sunlit would turn to dirt_with_grass no
matter what, but this happened without any context, so you could
get green patches of dirt_with_grass in the middle of a savannah or
even desert.
Dirt no longer turns to covered dirt unless it's within 1 node from
another dirt_with_grass or dirt_with_dry_grass or dirt_with_snow.
This makes dirt_with_grass "growback" a lot slower, since it now only
happens on the edges, but it retains the context nicely now.
If there is any dirt with a grass or dry grass plant, or snow on top,
and enough light, we'll convert it sporadically to dirt_with_grass
or dirt_with_dry_grass or dirt_with_snow.
This allows us to plant grass of our choice in a large dirt patch,
or in a region where otherwise that type of grass is not present.
This used to be done by 2 abms, but I've combined them in to a single
ABM that is ordered to run with maximum efficiency, solving for the
most common outcome first before attempting more complex checks.
This is technically "dirt with grass" that's just under a snow
cover, so in darkness the grass on these nodes will also die,
turning it into dirt.
This doesn't convert dirt_with_snow under snow.
This changes the drawtype of fences to NDT_CONNECTED nodebox drawtype.
These nodes are drawn by the client with the needed connections on
the fly as the scene is drawn. There is no logic needed by mods to
modify the nodes.
These fences connect to (1) other fences, (2) planks and (3) tree
trunks, but nothing else. They do not connect to stone, dirt, wool,
etc. This is done by the "connects_to" parameter, which takes groups
and node names.
Due to the way textures are wrapped, we can make these nodes look a
lot better by giving them a special tile.
This change requires minetest/minetest#3503.
